Replacing uPVC Window Handles
It is simple to swap the handles on upvc windows. upvc replacement door handles is important to make sure that the new handle is a good fit for the spindle carved out in the window mechanism.
If the steps below are followed properly the cockspur handle will be able to fit into most windows. The key is the step in the height of the handle.
What to Do You Look For?
A large portion of windows in the UK come with uPVC handles Over time, they will begin to show signs of wear and tear. If this occurs, the window handle can become loose or difficult to operate, which makes it necessary to replace it. Anyone who is proficient using a basic hand tool is able to complete this job.
The first step is to make sure that the handle is securely fixed to the frame of the window and in the open position. The next step is to find the screws or pins that secure the handle in place. They are usually located on the inside face of the handle and can be removed using a screwdriver or pliers.
When the handle has become loose, gently pull it away from its hinges. The next step is to find a new handle with the same design and size. This can be accomplished online or in an area DIY store, and the process should only take five minutes using an screwdriver.
When replacing the handle of a uPVC handle, it is important to take into consideration the step height. This is the distance from the bottom of the handle until it rests on the frame of the window. This is usually an average measurement, but it is essential that you determine the step height of your current handle prior to ordering an entirely new one.
Depending on the kind of handle you choose There are various sizes that are available. Inline handles are offered for uPVC window with lug centres of 31mm, while cockspur handles have lug centres of 43 millimetres. Tilt-and turn handles are typically found on uPVC windows. They feature a unique design which allows the window be tilted to allow for ventilation and then rotated to fully open the window.
The most common breakage in uPVC handles is that they crack inside instead of breaking off from the base section. This makes them difficult to open and therefore it is important to make sure that any replacement handle you buy has the same length of spindle that your current one.
Remove the old Handle
If the handles on your windows are damaged or incorrectly installed, they could cause double-glazed windows to not open or close correctly. They may even get stuck. There are a myriad of reasons for this including general wear and tear or the corrosion of the handle made of metal. In these situations it is crucial to replace the upvc window handle as quickly as you can in order to avoid further damage or loss of functionality.
When replacing the handles on windows made of upvc and handles, it is important to remove the handles that were previously installed from the window. To do this, begin by removing the screw that is covered when the handle is in its closed position. This should reveal another screw that once removed, you can then begin to remove the handle itself. It is possible to make the task simpler by using an electric screwdriver.
It is also important to be aware that screws may be hidden beneath plastic caps. It is recommended to remove the covers with the help of a Stanley knife. Once the old handle is removed, you should then take a look at the square cut on the base of the handle to make sure that the new window lock handles will work with it. This is important because you'll need to determine the length of the spindle on the previous handle to ensure that it is the same size as the window mechanism and handle spindle cut out.
The different kinds of upvc window handles are: Espag handles, which feature a central screw that will turn left or right; Cranked handles that have two screws and are found on tilt and turn upvc windows; and Spade handles, that have a flat arm and can be placed on either side of the window. When you have a suitable replacement, it's just a matter of screwing the handle into position and ensuring that the spindle is placed into the lock mechanism. After that, you can then tighten the handle to the window frame. The new upvc handles should now be secure.
Measure the Spindle
If you're replacing a Upvc window handle that has come off, it is likely because the spindle that holds it in place has become loose or damaged. In some instances, this could be fixed using pins or screws to tighten it. In some cases it is necessary to replace the handle. There are a few different types of upvc window handles. There are three kinds of handles: inline espagnolette, tilt-and-turn, and cockspur. Each handle type is installed and replaced in a different fashion.
Before purchasing a replacement handle it is important to know the size of the one you have. This will ensure that the new handle is the right size and will fit correctly within the window. All handles are sized according to industry standards, making it easy to determine the right size.
To measure the size of the handle, turn the window to the open position. You should be able see the size of the pin or screw that holds the handle. Then, use the ruler or tape measure to determine the length of the spindle. Once you know the length of your spindle, it is possible to purchase a replacement of the exact same length.
The step height of a upvc window handle is another factor to take into consideration when you are buying a replacement. The step height is measured from the base to the point at which the handle is placed on the frame. In general, this is approximately 21mm for uPVC windows or 9mm for aluminium. Dropping something in the space will allow you to determine how far the handle extends before it reaches an obstruction.
Cockspur handles may have different backsets depending on what kind of window you want to install them in. Inline Espag handles have the standard height of 43mm from centre to centre (2 fixing points). Cockspur handles have different backsets depending on the window they are placed in. This is because they feature an extension spur that extends from the handle and locks over the cockspur wedge striker plate.
Install the new handle
When you've picked a new handle, ensure that it is aligned to the screw holes in the door and secure it using the supplied screws. Install the latch lever in the same manner as the handle on the main handle when you're replacing the door handle. After that, attach the door trim to hide the mounting screws.

Tip: To remove the head of the metal from the wooden wedge, hold the handle so its wider end is resting on the floor and use a hammer to tap on the thin end of the handle. Be careful not to scratch the handle or spindle.